![]() If light comes back on again, customer to return for straight time electrical diagnostics. They turn on and off intermittently.ġ52068 CODE 61-1 Battery voltage failure CODE 17-1 L/R wheel sensor OPEN/SHORT CODE 24-2 R?F TCS normal OPEN SOL VALVE failure CODE 31-2Įngine retard command failure performed AVR test battery and alternator good Max output 142 amps cleared light & road tested on highway light did not comeback on. I drove it home no lights, once parked I shut off the engine, restarted it and the lights came back on. I took it to the honda dealership and they ran the initial tests and basically cleared the lights. The TCS and ABS lights come on and go away intermittently. I recently started having this trouble with my 2002 odyssey. (You have the ABS light on so refer to above first.)Ĭheck ground or a short between PCM and ABS/TCS control unit.Ĭheck for loose connectors at the ABS/TCS control unit. If the Check Engine Light or the ABS lights are on, check these first. TCS DTC 31: Engine retard command (PFINH) signal If no, then an intermittent failure - OK. Does the ABS light come on? If yes, check the charging system. Malfunctioning Part Reference Pageġ2 Self-diagnosis could not detect any malfunctions.Ĥ5 Actuator front left outlet solenoid valveĤ6 Actuator front left inlet solenoid valveĤ1 Actuator front right outlet solenoid valveĤ2 Actuator front right inlet solenoid valveĥ1 Actuator rear right outlet solenoid valveĥ2 Actuator rear right inlet solenoid valveĥ5 Actuator rear left outlet solenoid valveĥ6 Actuator rear left inlet solenoid valveĪre the #1 and #9 the correct pins to short?Ĭheck Fuse # 50 (30A) in the Under-hood Fuse/Relay Box.Ĭheck Fuse # 14 (7.5A) in the Passenger's Under-dash Fuse/Relay Box.Ĭheck ground and a loose connection in the Under-dash Fuse/Relay Box and the ABS Control Unit.Ĭheck pump motor relay in the Under-hood ABS Relay Box.Ĭheck for open wire between ABS Relay Box and pump motor.Ĭheck for open wire from Under-hood ABS Relay Box to ABS Control Unit. Only the start code should appear, noĬode No. Warning lamp goes out after the erase operation has been completed.ģ. Within 12.5 seconds, ground the check terminal three times.Įach terminal ground must last more than 1 second. Disconnect the check terminal from ground (ABS warning lampĢ. HOW TO ERASE SELF-DIAGNOSTIC RESULTS (MALFUNCTION CODES)ġ. ![]() The indication then returns to the start code 12 to repeat (the indication will After that a maximum of three code numbers appear in the The indication begins with the start code 12. When several malfunctions occur at one time, up to three code numbers can be stored the latest malfunctionģ. by counting the number of times the warning lamp flashes on and off.Ģ. HOW TO READ SELF-DIAGNOSTIC RESULTS (MALFUNCTION CODES)ġ. However, when the ignition switch is turned from OFF to ON, the The indication terminates after 5 minutes. The ABS in a safe area to verify that it functions properly. After making certain that warning lamp does not come on, test Check warning lamp for deactivation after driving vehicle over 30ġ1. Disconnect the check terminal from the ground. Rerun the self-diagnostic results mode to verify that the malfunctionĩ. After the malfunctions are repaired, erase the malfunction codesĨ. ![]() Then make the necessary repairs following the diagnostic procedures.ħ. Verify the location of the malfunction with the malfunction codeĬhart. After 3.0 seconds, the warning lamp starts flashing to indicateĦ. Turn ignition switch ON while grounding terminal 9.ĥ. Ground terminal 9 of Data Link Connector with a suitable harness.Ĥ. Drive vehicle over 30 km/h (19 MPH) for at least one minute.ģ. Location of the malfunction is indicated by the warning lamp flashing.ġ. Results mode, ground the self-diagnostic (check) terminal located on Data Link Connector. When a problem occurs in the ABS, the warning lamp on the instrument panel comes on. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |